Red dot side mount for installation of red dots with compatible footprints.
Side red dot mount works as a replacement of a thumb rest.
You can combine it with Toni System thumb rest for side mount and with Toni System charging handle.
Full list of compatible red dots and CZ models is below.
Specification
- original Toni System product
- made of aluminium
- made in Italy
- screws included
Compatibility with CZs
This red dot mount is compatible with the following models:
CZ TS 2
- CZ TS 2 Deep Bronze
- CZ TS 2 Racing Green
- CZ TS 2 Orange
CZ TS 1
Compatibility with red dots
This red dot mount is compatible with the following red dots:
Shield RMSc standard
- ADE Advanced Optics RD3-018 Spike,
- ADE Advanced Optics RD3-021 Nuwa,
- Burris FastFire C,
- JPoint MRD,
- Olight Osight S,
- Olight Osight SE,
- Riton X3 Tactix PRD,
- Shield AMS,
- Shield AMSc,
- Shield OMSsc,
- Shield SMS,
- Shield SMS2,
- Shield SMSc,
- Shield RMS,
- Shield RMS2,
- Shield RMSc,
- Shield RMSsc,
- Shield RMSd,
- Shield RMSw,
- Shield RMSx,
- Sig Romeo Zero,
- Sig Romeo-X,
- Sightmark Mini Shot A-Spec M3,
- Swampfox Sentinel 1×16,
- UTG OP3 Mini Micro,
- Vector Optics Frenzy-S 1x16x22,
- Vector Optics Frenzy-S 1x17x24 MIC,
- Vector Optics Frenzy-S 1x17x24 SAS,
- Vector Optics Frenzy-S 1x17x24 MOS Multi Reticle,
- Vector Optics Frenzy-S 1x19x28,
- Vortex Defender CCW
Leupold DPP standard
- Bushnell RXS-100,
- Eotech EFLX,
- Holosun SCS 320,
- Leupold Delta Point Pro,
- Primary Arms GLX RS-15 ACSS Vulcan,
- Sig Romeo 2,
- Sig Romeo-X PRO,
- Sig Romeo-X PRO Enclosed,
- Vortex Defender ST,
- Vortex Defender XL
Vortex Venom / Docter standard
- ADE Advanced Optics RD3-006 Huracan,
- ADE Advanced Optics RD3-009 Crusader,
- ADE Advanced Optics RD3-012 Delta,
- ADE Advanced Optics RD3-013 Bertrillium,
- ADE Advanced Optics RD3-015 Zantitium,
- Athlon Midas TSR1,
- Burris Fastfire 2,
- Burris Fastfire 3,
- Burris Fastfire 4,
- Noblex NV Sight II plus,
- Noblex NV Sight III,
- Noblex NV Sight C,
- Noblex NV Sight G,
- Leica Tempus,
- Leica Tempus 2,
- MAKdot SH,
- Sightmark Mini Shot M-Spec,
- Springfield Armory Hex Dragonfly,
- US Optics DRS 2.0,
- US Optics DRS 2.0 Enhanced,
- Vector Optics Frenzy 1x17x24,
- Vector Optics Frenzy-X 1x20x28,
- Vector Optics Frenzy-X 1x20x28 SIX,
- VictOptics V3 1x17x22,
- Vortex Venom,
- Vortex Viper
Installation
Remove the thumb rest and replace it with the red dot mount.
You should use loctite threadlocker on the screws.
No modificatoin required. You can switch back to your factory thumb rest any time.
Installation is possible to do by yourself with basic tools.
